• 162804425

18 Gauge Pneumatic Brad Nailer F30

Short Description:


Product Detail

Overview
F30

18 Gauge Pneumatic Brad Nailer F30

18 Gauge Pneumatic Brad Nailer F30 ideal for a wide variety of finish applications, Designed with a aluminum body for strength and lightweight use.

● Tool-free depth-of-drive adjustment.

● Tool-free jam release.

● Drives 3/8 in. to 1-3/16 in. 18 guage F brad nails.

● High capacity magazine holds up to 100 nails.

● Lightweight aluminum alloy body weighs only 2.4 pounds.

Product Description

 

Model: 18 Gauge Pneumatic Brad Nailer F30
Air Tool Type: Air Nailer
Tool Diamensions: 197mm x 57mm x 235mm
Net Tool Weight: 1.10kgs(2.42 lbs)
Body Material: Aliminum Body
Operate Pressure: 60-100psi (4-7bar)
Load Capacity: 100 nails
Nails Type: 18 Guage F Brad Nails
Nails Head Diameter: 0.075″(1.9mm) x 0.050″(1.3mm)
Nails Shank Diameter: 1.05mm
Nails Length: 3/8″(10mm)~1-3/16″(30mm)

f30

F BRAD NAILS

18 Guage F Brad Nails
Nails Head Diameter:0.075″(1.9mm) x 0.050″(1.3mm)
Nails Shank Diameter:1.05mm
Nails Length:3/8″(10mm)~1-3/16″(30mm)
Features

 Lightweight and well balanced for easy operating.

 Superior power with hardened one piece piston for professional application.

 Open nose design for easy extraction of a jammed nail.

 Tool free depth of drive adjustment for flush or counter sunk drive into varying material.

 Hardened claw tip,reduces wear and limits slippage when driving at a stand angle.

Application

Decorative and furniture trim.

Picture frame assembly.

Interior and exterior trim.

Cabinet work.

Crafts.

F30

Our Services
No.  Symptom Problems Solutions
1.1 Air Leak Air leak in the cylinder cap when tools don’t work 1.Loose head valve piston seal or o-rings . Check and replace the head valve piston set
2.Worn or damaged o-ring or cylinder cap gasket under cylinder cap Check and replace o-ring or cylinder cap gasket under the cylinder cap
1.2 Air leak in Trigger area  when tools don’t work 1.Damaged o-ring in trigger valve Check and replace  o-ring
2.Damaged o-ring in trigger valve stem Check and replace o-ring
3.Dirt in the trigger valve Check and clean the trigger valve
1.3 Air leak in cylinder cap when tools are working 1.Damaged head valve piston o-rings Check and replace  o-rings
2.Damaged seal under cylinder cap Check and replace seal
1.4 Air leak in nose when tools are working 1.Worn or damaged bumper Check and replace bumper
2.Loose driver(piston unit) thread Check and replace driver(piston unit)
1.5 Air leak in Trigger area when tools are working 1.Worn or damaged trigger valve head Check and replace trigger valve head
2.Damaged head valve piston o-rings Check and replace head valve piston o-rings
2 Failed to get driver(piston unit) back to the correct position completely. 1.The driver(piston unit) is not straight or the driver guide(nose) is wrong assembled. Straighten the driver(piston unit)  or verify driver guide(nose) and magazine
2.Worn or damaged nozzle Check and replace nozzle
3.The space between piston o-ring and  cylinder is too tight. Check if the cylinder is adequate lubrication or replace the o-ring on the piston.

  • Previous:
  • Next:

  • Write your message here and send it to us